Using the Protocols Panel

Introduction

In addition to using the Protocols Panel to view, draw, and manage protocol measurements, you can also use the Protocols Panel to display traces and points. You can perform protocol measurements and annotations for the current study on any viewport for a single or a multiframe series.

Prerequisites

Advanced Reporting (AR) is installed.
You are launching the Protocols Panel from an AR study with a procedure configured with an analysis configuration.

About This Task

The Protocols Panel displays on the right side of your screen.

Protocol steps are performed inside an image in the Viewer.
The measurement cursor displays as a Cross Hair when you are in measurement mode in the Protocols Panel.
You can choose to skip a protocol step. For additional information, see Skip a protocol step.
For measurements and calculations that have secondary values, such as AV VTI, the secondary values auto-populate the Protocols Panel when you complete the primary measurement or calculation.

Steps

From the Worklist page, select an AR study and either double-click or select Open Viewer from the context menu.
Click Protocols Panel on the Viewer toolbar to open the Protocols Panel.
Click a Protocol group in the Protocols Panel to display the protocol steps.
Position the cursor in the image and draw the protocol measurement.
Complete any of the following applicable steps.

If you want to ...	Complete these steps ...
Change a protocol measurement value.	In the image, do one of the following after exiting measurement mode by clicking ESC: Click and drag the protocol measurement to another location. Click and drag the measurement points to resize the measurement. In the Protocols Panel: Click the measurement text box, enter a different value, and press Enter. Changes made in the Viewer are reflected in the Protocols Panel, the Results overlay, and in the Clinical Reporting Application. Note: When you click in the measurement text box, Synapse displays the manually entered value.
Change the highlight color.	See Configuring Overlay Settings.
Change images while a protocol measurement is active.	Use any of the following: See J through Q Context Menu Options for the keyboard short cuts for the following options: Next Series or Previous Series Next Series Set or Previous Series Set Next RP Step or Previous RP Step Next Comparison or Previous Comparison Drag and drop. See Using Drag and Drop from Viewport to Viewport. Anywhere Series Picker. See Using Anywhere Series Picker in the Viewer.
Delete a measurement in the Protocols Panel.	Do one of the following: In the Protocols Panel, click the instance selector and click the X associated with the measurement instance you want to remove. In the Results overlay, hover over the Protocol measurement and click Delete to remove the measurement. Optional: Right-click the measurement annotation in the image to display the context menu and select Reset Annotations to delete all measurements in a study. When you delete a measurement from the Results overlay, Synapse also deletes the measurement from the Protocols Panel and Clinical Reporting Application. Note: You can delete a measurement instance; however, you cannot delete calculated instances, such as MIN, MAX, AVG, and LAST.
Display or close the image context menu.	You can view the image context menu in a list or icon format. To display the image context menu, right-click inside an image. To close the image context menu, press the Esc key. See Using the Image Context Menus.
Display or hide the Protocols Panel.	Click Protocols Panel on the Viewer toolbar once to display the Protocols Panel. Click Protocols Panel again to hide it.
Display or hide the protocol steps.	Click a protocol group in the Protocols Panel once to display the protocol steps. Click it again to hide all protocol steps and display only the protocols group.
Export Protocol measurements and Results overlay with image.	See Exporting and Printing Images.
Manually enter a value in the Protocols Panel.	See Change a protocol measurement value.
Move the Protocols Panel outside of the image.	Not supported.
Perform fetal measurements.	See Performing Fetal Measurements.
Perform phased measurements.	See Performing Phased Measurements.
Reposition a measurement.	Click and drag the measurement to a new location in the current image.
Reposition the Protocols Panel.	Not supported.
Show protocol measurement.	Click Show Points to display all of the measurement points for the selected instance in the image.
Skip a protocol step.	Click the next protocol step in Protocols Panel. Note: If a manual measurement is configured to skip, Synapse skips that measurement and the next measurement in the Protocols Panel becomes active. If a manual measurement is configured not to skip, Synapse highlights the measurement and waits until you add a manual measurement.
Terminate a measurement and leave measurement mode.	Press the Esc key once to terminate a measurement.
Use the Lock tools option.	This option is not supported.
View all measurement instances of a protocol step.	Click Instance Selector to display all measurement instances for a protocol step. Synapse displays the following values when displaying instances: LAST AVG MIN MAX
View a specific measurement instance of a protocol in the current image.	Click Instance Selector to display all measurement instances for a protocol step. Click Show Points to display all of the measurement points for the selected instance in the image.

Results